The number is how far away, in mm, you have the tool before probing, This allows the software to stop if it doesn't find the probe.
In the Probe distance/direction box a positive number means your z axis has to move up to touch the plate, a more positive z value, and a negative number means the Z axis has to move down, a more negative Z value. Cheap Wood Routers, Buy Quality Tools Directly from China Suppliers:Cnc Milling Z Axis Tool Setting Touch Plate Probe Mach3 Router Mill Cnc Engraving Machine Auto Check Instrument Setting Probe Enjoy Free Shipping Worldwide Limited Time Sale Easy Return. You may have to adjust this value after testing, I had to increase by. Put in your plates thickness in the Touch Plate Thickness box. China leading provider of Fiber Laser Cutting Machine and CNC Plasma Cutting Machine, Shandong Regiant CNC Equipment Co.,Ltd is CNC Plasma Cutting Machine factory. The Kit Comes with 1- Stainless Steel 0.5mm thick touch plate 1- Wire, 1.5M (60'), 22AWG with a female dupont plug on one end already. It has nice flex to it but it can be bent if you would prefer a little angle to it. Instructions for use can be found here: Instructions.
This touch probe has the Dupont connector attached and is ready to plug into the Evolution series or the E series CNCs. Now measure your touch plate thickness in mm, you will need this for UGS. The Touch Plate is 0.5mm thick stainless steel. Z Touch Probe is backordered and will ship as soon as it is back in stock. Retract Amount is how many mm the tool will move off plate after first touch and before second. You want this slow, so it gets an accurate touch.
The Slow Measure Rate is how fast it retouches the plate to set you z. Fast Find Rate is mm per min for the rapid to touch plate, I set it at 100, it's not too fast, but I don't want to damage the plate.
If, like me, you are only going to use the probe for Z you don't have to worry about End mill diameter. Units has to be millimeters, I could not get the probe to work with Inches.
This moves the Z axis up 5mm to let you remove the clamp and probe.įurther details can be found on the Milling Basics page.Open UGS and click the Windows menu item, then click Plugins, and click Probe Module. This tells the board it is now at 0.5mm above the Z plane Make sure this fits by entering your model number. All V1 Firmware is and has been ready to use this type of plate. Simply insert the plug into the plate, hit a button, and let the machine touch the plate and find it’s position. Then in the Mach 3, you need to setup the probe (Mach3 - Config-Ports and Pins-Input signals Probe enabled, the pin number type the one you use) and the Auto-Tool-Zero. The alligator clip should be connected to the Zmin negative, and the plate to the S (signal) pin. Our touch plate is designed for simple touching off in 3 directions without guessing or eyeballing distances. Cut and crimp the wire to a length suitable for your build. This is a DIY bag of parts because I know you all like to personalize things. FREE Shipping on orders over 25 shipped by Amazon. It has nice flex to it but it can be bent if you would prefer a little angle to it.ġ- Stainless Steel 0.5mm thick touch plateġ- Wire, 1.5M (60"), 22AWG with a female dupont plug on one end already.ġ- Alligator clamp, easily handle 1/8" to 1/4" endmillsġ-1/8 in x 1/4 in Neodymium Cylinder N42 (ND004) Magnet CNC Z-axis Router Tool Setting Probe Z-probe Touch Plate for CNC Engraving Machines. To create a touch plate, we purchased an inexpensive kit online, shown below. The GRBL firmware on the microprocessor sets the bit at Z0 on a workpiece. The Touch Plate is 0.5mm thick stainless steel. When a touch plate is activated, the router bit descends on the Z-axis and contacts the touch plate completing the circuit and a 5v pulse is sent to the controller.